Page not found

ERNiCrMo-3 material is suitable for the welding of nickel based alloys such as Inconel 625 and Incoloy 825, but also for dissimilar welds, e. G. Between stainless and nickel-based alloys and mild steel.

Standard: AWS A5.14  EN18274  ,ASME II, SFA-5.14, ERNiCrMo-3

Size: 0.8MM / 1.0MM / 1.2MM / 1.6MM / 2.4MM / 3.2MM / 3.8MM / 4.0MM / 5.0MM

Form: MIG  (15kg/spool),

TIG(5kg/box)

ErNiCrMo-3 Chemical Composition

C

Si

Mn

S

P

Cr

Mo

Ni

Ti

Al

Fe

Co

Nb+Ta

Cu

Others

≦       0.1

≦         0.

≦       0.5

≦     0.015

≦      0.015

20.0-23.0

8.5-  10.0

≧      62.0

≦       0.4

≦       0.4

≦        0.5

/

3.15-4.15

≦       0.5

≦       0.5

Usage: used for welding the INCONEL ALLOY 600/825/25-6MO, and other stainless steel with Mo by the way of gas metal arc welding, tungstun-inert-gas arc welding.

 

产品名称:钛焊丝
型号:TA1TA2 TA3TA5TA6TA7TC1TC2TC4TC6TC9TC10TC11等标准钛及钛合金,异型钛合金可以按照工厂的材质要求订单生产,钛焊丝系列均按照美国AWS标准生产。
规格:φ0.8~φ7.0
形状:盘丝,直丝
执行标准GB/T 3623-2007
用途:钛焊丝在焊接反应釜钛,储存酸性物质或碱性物质罐存管,钛化设备时使用。


钛焊丝使用注意事项:
1、施工人员和焊工应佩戴洁净的白细纱布手套(严禁佩戴棉线手套)。
2、经处理的焊区严禁用手触摸和接触铁制物品。
3、焊接工作尽可能在室内进行,环境风速应≤0.5m/s,避免受穿堂风影响。
4、焊接时应尽可能采用短弧焊接,采用小的焊接热输入,喷嘴与焊件保持70~80度的夹角。
5、对接管定位焊时,其对接间隙一般为0.5mm左右。
6、每道焊缝应尽可能一次焊完,必须接焊的焊缝,在焊前应将接口处清理干净,焊肉搭接长度为10~15mm。
7、焊接时,焊炬不应左右摆动,焊丝熔化端不得移出气体保护区。
8、施焊引弧时应提前送气,熄弧时不能马上抬起焊炬,应延后供气,直到温度降至250℃以下。
9、气体保护拖罩与焊炬的距离应以最短为佳,与管壁接触的间隙力求最小。进行管对接焊时,为了达到单面焊双面成形要求,焊接分两次进行:一次为封底焊接(封底焊时可以不用填充材料),另一次为成形焊接。多层焊时,必须等前一焊道完全冷却后,再焊下一焊道。


Nickel base Alloy Welding Wire

 

AWS

Type

Chemical Elements of code

Chemical composition.%

C

Mn

Fe

Si

Cu

Ni

Al

Ti

Cr

Nb/Ta

Mo

Other      Co .S.P.W

ERNiCrMo-3

SNi6625

NiCr22Mo9Nb

≤0.1

≤0.5

≤5.0

≤0.5

≤0.5

≥58.0

20.0-

23.0

3.0- 4.2

8.0-

10.0

ERNi-1

SNi2061

NiTi3

≤0.15

≤1.0

≤1.0

≤0.75

≤0.25

≥92.0

≤1.5

2.0-3.5

-

-

-

0.5

ERNiCr-3

SNi6082

NiCr20Mn3Nb

≤0.10

2.5~3.5

≤3.0

≤0.5

≤0.5

≥67.0

-

≤0.7

18.0~

22.0

2.0~ 3.0

ERNiFeCr-1

SNi8065

NiFe30Cr21Mo3

≤0.05

1.0

≥22

≤0.5

1.5-3

38-46

≤0.2

0.6-1.2

19.5-23.5

-

2.5-3.5

ERNiCu-7

SNi4060

NiCu30Mn3Ti

≤0.15

2.0-4.0

≤2.5

≤1.25

Bal

62.0- 69.0

≤1.25

1.5-3.0

P≤0.02

S≤0.015

ERCuNi

CuNi

1.0

0.4-

0.75

0.25

Bal

29.0-

32.0

0.2-0.5

0.5

ERNi-CI

0.1

0.3

0.2

0.1

0.2

99.2

S.P≤0.01

ERNiCrFe-5

≤0.08

≤1.0

6.0 – 1.0

≤0.35

≤0.5

≥70.0

14.7- 17.0

1.5- 3.0

Co≤0.12

P≤0.03

S≤0.015

ERNiCrMo-1

≤0.15

1.0-2.0

18.0- 21.0

≤1.0

1.5-2.5

Bal

1.5-2.5

5.5- 7.5

Co≤2.5

P≤0.04

S≤0.03

ERNiCrMo-11

≤0.03

≤1.5

13.0- 17.0

≤0.8

1.0-2.4

Bal

28.0- 31.5

0.3-1.5

4.0-6.0

Co≤5.0

P≤0.04

W:1.5-4.0

ERNiCrMo-2

0.05- 0.15

≤1.0

17.0- 20.0

≤1.0

≤0.5

Bal

20.5- 3.0

8.0- 10.0

Co:0.5-2.5

W:0.2-1.0

P≤0.04

ERNiCrMo-3

0.1

 

≤0.5

≤5.0

≤0.5

≤0.5

≥58.0

≤0.4

≤0.4

20.0-23.0

3.15- 4.15

8.0- 10.0

P≤0.02

S≤0.015

ERNiCrMo-4

≤0.02

≤1.0

4.0-7.0

≤0.08

≤0.5

Bal

14.5-17.0

15.0-17.0

Co≤2.5

W:3.0-4.5

V≤0.35

ERNiCrMo-7

≤0.015

≤1.0

≤3.0

≤0.05

≤0.5

Bal;

≤0.7

14.0- 18.0

14.0-118.0

Co≤2.0

W:≤0.5

P≤0.04

ERNiCrMo-8

≤0.03

≤1.0

Bal

≤1.0

0.7- 1.2

47.0- 52.0

0.7- 1.5

23.0- 26.0

5.0- 7.0

0.5

ERNiCrMo-9

≤0.015

≤1.0

18.0- 21.0

≤1.0

1.5- 2.5

Bal

21.0- 23.5

≤0.5

6.0-   8.0

Co≤5.0

P≤0.04

W≤1.5

ERNiCrMo-10

≤0.015

≤0.5

2.0- 6.0

0.08

≤0.5

Bal

20.0- 22.5

12.5- 14.5

Co≤2.5

W:2.5-3.5

V≤0.35

ERNiCrCoMo-1

0.05- 0.15

≤1.0

≤3.0

≤1.0

≤0.5

Bal

0.8- 1.5

≤0.6

20.0- 24.0

8.0- 10.0

Co:10.0-15.0

S≤0.015       P≤0.03

ErNiFe-CI

≤0.1

0.5-1.5

Bal

≤0.2

≤0.2

≥55.0

Other≤1.0 S≤0.02       P≤0.02

ERNiFeCr-2

≤0.08

≤0.35

Bal

≤0.35

≤0.30

50.0- 55.0

0.2- 0.8

0.65- 1.15

17.0- 21.0

4.75- 5.5

2.8- 3.30

other≤0.5

ErNiMo-3

≤0.12

≤1.0

4.0- 7.0

≤1.0

≤0.5

 Bal

4.0- 6.0

23.0- 26.0

Co≤2.5

W≤1.0

V≤0.6

 

 

Inconel 713C Round Bar

We Manufacture and Sell Inconel 713C Round Bar by Investment Casting,Bar Diameter form 6.0mm-300mm.More Detail information,Please contact us!

Inconel 713C is a nickel-chromium alloy that is ideally suited for jet engine gas turbine blades.Inconel 713C offers outstanding resistance to thermal fatigue and good castability while offering exceptional rupture strength at 1700°F (927°C). 

Inconel 713C Round Bar Chemical Compositons:

Alloy

%

Ni

Cr

Fe

Mn

Si

Mo

Zr

Ti

Cu

Co

Al

C

S

713C

Min.

Bal

12.0

-

-

-

3.8

0.05

0.5

-

1.8

5.5

-

-

Max.

14.0

2.5

0.25

0.5

5.2

0.15

1.0

0.5

2.8

6.5

0.20

0.015

Inconl 713C Round Bar Physical properties

Density

7.913 g/cm³

Melting point

1260℃-1288℃

Inconel 713C Products Mechinabity Physical                     

 ●High-speed tungsten-cobalt or molybdenum-tungsten-vanadium toolsCutting lubricants:

Chlorinated, sulfurized  fatty mineral oil

Rich emulsion of 10 parts water and 1 part soluble oil

Aluminum oxide

Vitrified bond of medium or soft hardness and medium open structure

Use 1 pound of sal soda with 25 gallons of water, or chemically active grinding coolant

Inconel 713C Weledablity                                                   

  • Inconel 713C can be used in applications using very low restraint

  • Use Inco-Weld A electrode

  • Flash-butt weld

  • Inconel 713C is also good for hydrogen-atmosphere brazing with normal high-heat brazing alloy with electroplated mating surfaces

Inconel 713C Applications 

Inconel 713C is most commonly used for jet engine gas turbine blades.


Name

Stainless Steel Seamless Pipe/Tube

Available Size

O.D.: 6mm – 630mm / DN 6 – 600 / NPS 1/8’’ – 24’’

W.T.: 0.9mm – 40mm  Sch 5S – Sch XXS

Length: ≤ 24000 mm

Austenitic/ Super Austenitic  Steel

304, 304L, 304H, 316, 316L, 316Ti, 316H, 316Mod, 317L, 317Mod, 321, 321H, 309S, 309H, 310S, 310H, 347H, S31254904LTPXM-19

Duplex/Super Duplex Steel

S31803(SAF2205), S32750(SAF2507), S32760

Nikel Alloys

Monel 400, Inconel 600, Inconel 625, Incoloy 800/H/T, Incoloy 825

Special Metarial

Custom produced per your requirements.

Specification

ASTM/ASME A312, A269, A213, A511, A789, A790

ASTM SB163, SB165, SB167, SB407, SB423, SB444

EN10216-5 TC1, TC2, DIN 17456, DIN17458

JIS G3459, G3463, GOST 9940, GOST 9941

Quality Control

ISO 9001:2000, Pressure Equipment Directive 97/23/EC & AD2000-W0, RTNGOST, IQNET

Classification Society Approvals

BV, DNV, LR,GL,ABS, NK, KR, CCS.

GH3030/80Ni-20Cr/3-435/XH78T High Temperature Alloy  

GH3030/80Ni-20Cr solid solution strengthening type high temperature alloy is the early development of ni – cr solid solution strengthening 20 80 type high temperature alloy, the chemical composition is simple, under 800 ℃ has satisfactory heat intensity and high plasticity, and has good oxidation resistance, thermal fatigue, cold stamping and welding performance. Alloy after solid solution treatment for single-phase austenitic, stability in use process organization. Main products are cold rolled sheet, also can supply the rod, ring, wire and tube products such as deformation. 

Trade Name: China GH3030,Russia 3-435, XH78T ,80Ni-20Cr

GH3030/80Ni-20Cr Chemical Composition:

Alloy

%

Cr

Fe

Ni

C

Mn

Si

V

Cu

Al

P

Ti

S

GH3030

Min

19.0


Bal




0.1




0.15


Max

22.0

1.5

Bal

0.12

0.7

0.8

0.5

0.2

0.15

0.03

0.35

0.02

GH3030/80Ni-20Cr Physical Properties:

Density

8.40 g/cm3

Melting point

1374℃-1420 ℃

Coefficient of Thermal Conductivity (λ/(W/m•°C) )

15.10 (100°C).

Specific Heat Capacit(J/kg•°C )

565.20

Linear Expansibility (a/10-6°C-1 )

12.80 (20~100°C )

GH3030/80Ni-20Cr/3-435/XH78T Products Specifactions in Sekonic

Bar/Rod:

Wire/Welding Wire

Pipe/Tube:

Sheet/Plate:

Diameter:Φ5.0mm-Φ500mm

Length6000mm

Forged Bar,Hot rolling Bar,Cold draw rod

Diameter:Φ0.05mm-Φ8.0mm

Coil Wire,Cut length wire, Spool Wire

O.D.: 0.3mm – 630mm

W.T.: 0.08mm – 40mm

 DN 6 – 600 / NPS 1/8’’ – 24’’

 Sch 5S – Sch XXS

Length: 24000 mm

Seamless Tube,Welded Tube,Capillary Tube,U Tube

Thickness≧0.3mm;

 Width2000mm

Length≦12000

Hot Rolling Sheet,Cold Rolling Sheet,Forging Plate

GH3030/80Ni-20Cr Other Forms,Such as Ring,Fasteners,Ect,Can be Produce.

*Surface: Bright,Picked White,Back

*Heat Treatment: Solution Annealed,Aged Harden,Ect.

*Tolerance :according to Both confirmation

GH3030/80Ni-20Cr Application :

To be used for production work under 800 ℃ of turbine engine combustion chamber components and under 1100 ℃ antioxidant but other high temperature alloy small parts. 
GH3030 has strong thermal and cold properties, used to make all kinds of chemical equipment and related accessories

Stainless Steel Capillary Tube :

    Stainless steel is a production material that will not easily rust and has superior acid and corrosion resistance. Stainless steel capillary tube or pipe is produced by advanced welding process: pull-out from the processing.

     Prestige Industries pledge the quality and quantity according to your requirements  controling the inside diameter steel pipe wall thickness and tolerance, abrasive polishing process is in full compliance with SGS environmental protection requirements.

     We can Supply stainless steel capillary tube according to your requirements.

Name

Stainless Steel Capillary Tube

Standard

ASTM A312, A249, A269 and A270

Material Grade

304, 304L, 316, 316L

Size Range

1) Outer diameter:≥0.2mm

2) Wall thickness: ≥0.05mm

Length

6m or as customers' request

Tolerance

a) Outer Diameter:  +/-0. 15mm 

b) Thickness: +/- 0.02mm

c) Length:+/-4. 5mm - 0mm 

Surface

180G, 320G, 400G Satin / Hairline(Matt Finish, Brush, Dull Finish)

400G, 500G, 600G or 800G Mirror finish

Application

Ornamental tubes, Decoration construction, upholstery, industry instruments

Test

Squash test, Extended test, Water pressure test, Crystal rot test, Heat treatment, NDT

Chemical Composition 

of Material

Grade

C

Si

Mn

P

S

Cr

Ni

Mo


304

≤0.08

≤1.00

≤2.00

≤0.045

≤0.030

18-20

8-10.5

-


316

≤0.08

≤1.00

≤2.00

≤0.045

≤0.030

16-18

10-14

2.0-3.0




















































Mechanical Property

Material Item    

304

316

Tensile Strength

≥520

≥520

Yield Strength

≥205

≥205

Extension

≥35%

≥35%

Hardness (HV)

<200

<200

Stainless Steel Capillary Tube Applications:

1) Medical device industry
2) Temperature-guided industrial temperature control, sensors used pipe,tube thermometer
3) Pens care industry core tube
4) Micro-tube antenna, various types of small precision stainless steel antenna
5) Variety of electronic small-diameter stainless steel capillary
6) Jewelry needle punch
7) Watches
8) Car antenna tube
9) Laser engraving equipment
10) Fishing gear, accessories
11) Mobile phone and computer stylus


Capillar Tube

Material:

Inconel Alloy,Monel Alloy ,Hastelloy Alloy, Titanium Alloy,Stainless Steel

O.D

0.33 –5.0 mm

W.T

0.08 – 0.2 mm

Length

As for your requirement

Standard

ASTM, GB, AISI, JIS, DIN, etc

Delivery Time

10~50 days ,according to customer’s quantity

Delivery Condition

Pickled, polished, bright annealed, electrolytic polished

Package

Plastic bag for each bundle or as for your requirement.

Payment

100% irrevocable L/C at sight, or T/T in advance

 Capillar Tube Application:

  • Scientific research.

  • Medical Device Industry injection needles,needle tubes.

  • Chemical industry.

  • Thermal conductivity temperature control device,The sensor tube.

  • Instrument tube,miniature antenna tube.

  • Jewelry punch pin,watch insustry Watchband accessories.


STELLITE 6 is the most widely used of the wear resistant cobalt-based alloys and exhibits good all-round performance. It is regarded as the industry standard for general-purpose wear resistance applications.

Trade Name: Stellit 6; UNS R3006;AMS 5387C-2001

Stellite 6 Chemical components                                                            

C Cr  Si W Fe Mo Ni Mn B Co
1.2 28 1.1 4.5 3
3 1
bal
*The chemical composition shown above is an outline only,and should not be taken as a full specification.
*Note that cored wire may have higher Fe contents than other product forms.

Stellit 6 Physical property (Room Temp.)

 Density
(lb/in³)
Specific 
Gravity
Solidus Liquidus Specific heat
(J/kg·K)
Magnetic
Permeability
Electrode
Potential
Electrical
Conductivity
Electrical
Resistivity
0.305 8.46 2340°F 2540°F 0.101°F
Btu/lb-
<1.2@200
Oersteds
-0.25
 Volts
1.9%IACS
(Int. Annealed Copper Std.)
41.73
microhms-inch

Stellite 6 Thermal Properties-Conductivity&Expansion

              Thermal Expansion Coefficient         Thermal Conductivity by Temperature
       °F Microinch/ 
inch-°F
      °C Microns/
m-°C
      °F Btu/ft2/in/
hr/°F
     °C     W/mk
     212      6.3      100 11.34      70    102.7    21.11    14.82

Our cobalt base alloys are available as cobalt rods,cobalt electrodes,cobalt wire and cobalt powder.Cobalt alloys are used primarily for wear applications,Its unique combination of wear resistance, strength and corrosion resistance make it adaptable to many harsh environments.Cobalt alloys are selected for its excellent esistance to the widest combination of wear types including adhesive wear,abrasion, erosion,contact fatigue, thermal shock, cavitation wear,corrosion and oxidation.The degree to which the cobalt alloys retain these properties assures its unique position in the wear technology field.

Cobalt-Based Alloy Bare Rod:

- AWS RCoCr-C (Stellite 1)It has excellent wear and heat resistance at high temperature.Recommended use for making valve seal inserts , rotating sealing ring, drill heads, cutter edge ,etc

- AWS RCoCr-A (Stellite 6)The most widely used Cobalt Alloy with good mechanical properties at different temperatures,Recommended use for making valve seat material,hot shear blade,high temperature valve,turbine blade,etc.

- AWS RCoCr-B (Stellite 12)It has excellent resistance on high heat, corrosion and abrasion.Recommended use for making high-pressure valve, shear edge, sawteeth, etc

-AWS RCoCr-B (Stellite 21)It has excellent resistance on high heat,corrosion and abrasion.Recommended use for making fuild valve,brass casting die , vlave seat, etc.


We produce Titanium nut many according DIN934 our productes strictly executing the system requirements of ISO9001:2008 and our production management team are focusing on the lean six sigma methodology. Our products are in accordance with international standards. 

Item Name

Titanium  Nut

Material

Titanium and its alloy

Grade

Gr1,Gr2,Gr5,Gr7,Gr9,Gr12 ect

Standard

DIN 934/ISO/JIS

Specification

M2 , M2.5 , M3 , M3.5 , M4 , M5 , M6 , M8 , M10, M12, M16 , etc.

Surface Treatment

Polishing, Anodizing, Black oxidation

Color

Ti natural, Gold, Blue, Purple, Green,ect

Features

Light weight, Acid and alkali resistance, Anti-corrosion, Excellent mechanical strength etc.

Applications

Equipment accessories: Airplane, Ship, Bicycle, Motorcycle, Auto, Medical,

Chemical, Wheel, Sports, Anchor, Weapon, etc.

Titanium Nut Photos at Sekoinc 

Titanium Nuts.gif

Titanium Nuts Specification

DIN934(HEXAGON NUTS)

D

S

E

N

M3

5.5

6.01

2.4

M3.5

6

6.01

2.8

M4

7

7.66

3.2

M5

8

8.76

4

M6

10

11.05

5

M7

11

12.12

5.5

M8

13

14.38

6.5

M10

17

18.9

8

M12

19

21.1

10

M14

22

24.49

11

M16

24

26.75

13

M18

27

29.56

15

M20

30

32.95

16

M22

32

35.03

18

M24

36

39.55

19

M27

41

45.2

22

M30

46

50.85

24

M33

50

55.37

26

M36

55

60.79

29

Titanium nut d.gif

DIN6923(HEXAGON NUTS WITH FLANGE)

D

M5

M6

M8

M10

M12

M14

M16

M20

-

-

M81×1

M101×1.25

M12×1.5

M14×1.5

M16×1.5

M20×1.5

-

-

-

(M10×1)

M12×1.25

-

-

-

P1)

0.8

1

1.25

1.5

1.75

2

2

2.5

C

1

1.1

1.2

1.5

1.8

2.1

2.4

3

Da

Min

5

6

8

10

12

14

16

20

Max

5.75

6.75

8.75

10.8

13

15.1

17.3

21.6

Dc

Max

11.8

14.2

17.9

21.8

26

29.9

34.5

42.8

Dw

Min

9.8

12.2

15.8

19.6

23.8

27.6

31.9

39.9

E

Min

8.79

11.05

14.38

16.64

20.03

23.36

26.75

32.95

M

Max

5

6

8

10

12

14

16

20

Min

4.7

5.7

7.6

9.6

11.6

13.3

15.3

18.9

M1

Min

2.2

3.1

4.5

5.5

6.7

7.8

9

11.1

S

Nominalsize=Max

8

10

13

15

18

21

24

30

Min

7.78

9.78

12.73

14.73

17.73

20.67

23.67

29.67

R2)

Max

0.3

0.36

0.48

0.6

0.72

0.88

0.96

1.2


Titanium wire mesh is weaved by titanium wire; we can provide commercial pure titanium and kinds titanium wire mesh. It can be used in screening and filtering in acidic and alkaline environments, Gas-liquid filtration and other media separation. Sekonic Metals has been specialized in titanium wire mesh production for many years. Our titanium mesh has stabilize filtering characteristics

Item

Titanium Mesh

Type

Gr1,Gr2,Gr3,Gr4,Gr5,Ti6Al4V-ELI,Gr7,Gr9,

Thickness

0.5 to 2.5mm

Mesh Size

3*2mm  3*4mm  3*6mm  4*8mm  4.5*12.5mm

Thickness:0.5mm-2.5mm

Width: 50-1200mm

Length: 50-2400mm

Technique

Titanium plate/sheet——-Punching——–Pulling——Anneal(Leveling)—–Acid-Washing

MOQ.

5kg

Test and Quality

1.ISO 9001:2008

2.Mechanical properties test,

3.inspection ensure the materials meet destructive and non-destructive test  according to industry and customer specification

Applications

1.Chemical processing, medical instruments etc.

Load port

Shanghai

Packing box

Non-wooden case, single board burlap or as order.

Payment

1. T/T, L/C, Western union,

2.Prepaid 30% T/T against PI, pay for balance before delivery.

Delivery time

7 to 20days after confirmed

The specificationwould be changed by the customers' requirements.

Titanium Mesh Photos At our Company

Titanium mesh t.gif

We Manufacure Titanium Foil & Strip strictly according to national standard GB/T3621-2007 and American standard ASTM B265 executive production, specifications according to customer requirements of rolling.

Titanium Foil/Titanium Strip

Production Name

Titanium Foil/Titanium Strip

Grade

GR1, GR2, R5, 6AL4V Eli, GR7, GR9, GR12, GR23

TB3, TB6, TC4, TC6, TC11, TC17, TC18

Size

Thickness: 0.32mm-0.5mm or as your request

Standard

ASTM B265

Supply status

M (Y/ R/ ST)

Application

chemical, industry, electronic industry etc.

Feature

High corrosion resistance, low density, good thermal stability

Technics

Cold rolling

Surface

Bright, Polished, Pickling, Acid cleaning, Sandblasting

Packing

Export Standard Woodcase or as customer's require

MOQ

5 kilograms

Payment terms

T/T, L/C, D/A, D/P, Escrow, Western Union, PayPal

Certificate

ISO 9001:2008; The third test report; TÜV Rheinland; Supplier Assessment Certificate

Supply ability

2 Tons Per month

Delivery time

5—40days according to the quantity and process of the product

Quality and test

DPI, PMI, RT, Hardness test, Hydrostatic etc.

Titanium Foil/Titanium Strip Photos At Sekonic 

titanium Foil.jpg

Titanium Foil/Titanium Strip mechanical properties in the roomtemperature

Tensile Requirements
Grade Tensile strength(min) Yield strength(min) Elongation(%)
Ksi Mpa Ksi Mpa
Gr1 35 240 20 138 24
Gr2 50 345 40 275 20
Gr5 130 895 120 828 10
Gr7 50 345 40 275 20
Gr9 90 620 70 438 15
Gr12 70 438 50 345 18

Titanium Foil& Strip Material Chemical compostions:

Grade

ELEMENT  COMPOSITION , %

Ti

AL

V

Fe

C

N

H

O

Sn

Pa

Others D,E,Fmax

Grade 1

Balance

-

-

0.2

0.08

0.03

0.015

0.18

-

-

0.4

Grade 2

Balance

-

-

0.3

0.08

0.03

0.015

0.25

-

-

0.4

Grade 3

Balance

-

-

0.3

0.08

0.05

0.015

0.35

-

-

0.4

Grade 4

Balance

-

-

0.5

0.08

0.05

0.015

0.4

-

-

0.4

Grade 5

Balance

5.5-6.75

3.5-4.5

0.4

0.08

0.05

0.015

0.2

-

-

0.4

Grade 6

Balance

4.0-6.0

-

0.5

0.08

0.03

0.015

0.2

2.0-3.0

-

0.4

Grade 7

Balance

Pd 0.12-0.25


0.3

0.08

0.03

0.015

0.25

-

0.12-0.25

0.4

Grade 9

Balance

2.5-3.5

2.0-3.0

0.25

0.08

0.03

0.015

0.15

-

-

0.4

Grade 12

Balance

Mo 0.2-0.4

Ni 0.6-0.9

0.3

0.08

0.03

0.015

0.25

-

-

0.4

We Manufacure Titanium Sheet & Plate strictly according to national standard GB/T3621-2007 and American standard ASTM B265 executive production, specifications according to customer requirements of rolling.

Titanium Sheet & Plate

Product Name

Titanium Sheet & Plate

Material

GR1, GR2, R5, 6AL4V Eli, GR7, GR9, GR12, GR23 ect

TB3, TB6, TC4, TC6, TC11, TC17, TC18 ect

Standards

GB/T3621-2007 GB/T13810-2007 ASTM B265ASTM F136ASTM F67AMS4928

Demension

T 0.5-1.0mm x W1000mm x L 2000-4000mm T 1.0-5.0mm x W1000-1500mm x L 2000-3500mm T 5.0- 30mm x W1000-2500mm x L 3000-6000mm T 30- 80mm x W1000mm x L 2000mm ,ect

Technique

Hot forging, Hot rolling,Cold rolling,Annealing,Acid pickling

Payment

T/T, L/C ,Paypal as your inquiry

Certificate

ISO 9001:2008, The third test report

Supply Ability

1000 kg Per month

Delivery

Within 15~30 days

Titanium Sheet & Plate at Our Company Photos:

titanium plate.gif

Titanium Sheet & Plate Material Chemical compostions:

Grade

ELEMENT  COMPOSITION , %

Ti

AL

V

Fe

C

N

H

O

Sn

Pa

Others D,E,Fmax

Grade 1

BAL

-

-

0.2

0.08

0.03

0.015

0.18

-

-

0.4

Grade 2

BAL

-

-

0.3

0.08

0.03

0.015

0.25

-

-

0.4

Grade 3

BAL

-

-

0.3

0.08

0.05

0.015

0.35

-

-

0.4

Grade 4

BAL

-

-

0.5

0.08

0.05

0.015

0.4

-

-

0.4

Grade 5

BAL

5.5-6.75

3.5-4.5

0.4

0.08

0.05

0.015

0.2

-

-

0.4

Grade 6

BAL

4.0-6.0

-

0.5

0.08

0.03

0.015

0.2

2.0-3.0

-

0.4

Grade 7

BAL

Pd 0.12-0.25


0.3

0.08

0.03

0.015

0.25

-

0.12-0.25

0.4

Grade 9

BAL

2.5-3.5

2.0-3.0

0.25

0.08

0.03

0.015

0.15

-

-

0.4

Grade 12

BAL

Mo 0.2-0.4

Ni 0.6-0.9

0.3

0.08

0.03

0.015

0.25

-

-

0.4

 Titanium Sheet mechanical properties in the roomtemperature:

      

      Grade

Tensile Strength(min)

Yeild Strength(min)

Elongation(%)

ksi

MPa

ksi

MPa

1

35

240

20

138

24

2

50

345

40

275

20

5

130

895

120

828

10

7

50

345

40

275

20

9

90

620

70

438

15

12

70

438

50

345

18

We Manufacure Titanium Pipe & Tube such as Titanium Weld Pipe, Titanium Seamless Pipe.Titanium Heat-exchanger Tube strictly according to American standard ASTM B337 or ASTM B338 executive production, specifications according to customer requirements.

Product Name

Titanium tube,Titanium pipe

Materials

Gr.1, Gr.2,Gr.5,Gr.7, Gr.9, Gr.12 ect.

Standards

ASTM B337,ASTM B338,ASTM B861,ASTM B862

Specification

OD. 6mm~13mm Max Length 4m OD.13mm~114.3mm, Max Length 15m WT.0.3mm~12mm

Payment

T/T, L/C ,Paypal as your need

Certificate

ISO 9001:2008, The third test report

Supply Ability

1000 kg Per month

Delivery

Within 15~30 days 

Titanum Tube Standards and Specifications

Titanium welded pipe for heat

exchanger equipments

Titanium welded pipe for Chemical&Oil Industry

ASTM B338,

ASTM B862

Gr1 GR2 GR7 GR12

OD (10.3~914) = (1/8~36)Inch

WT (0.5~30.96) = (0.049~1.219) Inch

Length》12000mm

Titanium Seamless Tube For

(Heat Exchanger )

ASTM B338,

ASTM B337,

ASTM B861

GR1 GR2 GR3 GR5 GR6 GR7 GR9 GR12 GR16 GR17 etc.

OD (1.5~420) ×WT (0.3~16 )  Length 18000 mm

Titanium Pipe/Titanium Tube Types





Titanium Weld Pipe

Titanium Seamless Tube

Titanium Heat-exchanger Tube

Titanium Pipe/Titanium Tube Material Chemical compostions:

Grade

ELEMENT  COMPOSITION , %

Ti

AL

V

Fe

C

N

H

O

Sn

Pa

Others D,E,Fmax

Grade 1

Balance

-

-

0.2

0.08

0.03

0.015

0.18

-

-

0.4

Grade 2

Balance

-

-

0.3

0.08

0.03

0.015

0.25

-

-

0.4

Grade 3

Balance

-

-

0.3

0.08

0.05

0.015

0.35

-

-

0.4

Grade 4

Balance

-

-

0.5

0.08

0.05

0.015

0.4

-

-

0.4

Grade 5

Balance

5.5-6.75

3.5-4.5

0.4

0.08

0.05

0.015

0.2

-

-

0.4

Grade 6

Balance

4.0-6.0

-

0.5

0.08

0.03

0.015

0.2

2.0-3.0

-

0.4

Grade 7

Balance

Pd 0.12-0.25


0.3

0.08

0.03

0.015

0.25

-

0.12-0.25

0.4

Grade 9

Balance

2.5-3.5

2.0-3.0

0.25

0.08

0.03

0.015

0.15

-

-

0.4

Grade 12

Balance

Mo 0.2-0.4

Ni 0.6-0.9

0.3

0.08

0.03

0.015

0.25

-

-

0.4

Titanium Pipe/Titanium Tube mechanical properties in the roomtemperature:

      Grade

Tensile Strength(min)

Yeild Strength(min)

Elongation(%)

ksi

MPa

ksi

MPa

1

35

240

20

138

24

2

50

345

40

275

20

5

130

895

120

828

10

7

50

345

40

275

20

9

90

620

70

438

15

12

70

438

50

345

18



WhatsApp Online Chat !